Welcome to SENFENG. LoginRegisterSite MapFavorite Contact Us简体中文Pусский한국
Senfeng News
Current location: Home»SENFENG News Center » Consulting Center » FAQ » common problems for laser cutting engraving system

Recommended Products

Senfeng300W/500W/750W Laser Cutting Machine For Metal
Senfeng300W/500W/750W Laser Cutting Machine For Metal
1)working area:2500mm*1300mm or 3000mm*1500mm
2)fiber laser power:300W/500W/750W/1000W/1200W/1500w
SF1626SCAutoFeedingTextile Laser Cutting Machine
SF1626SCAutoFeedingTextile Laser Cutting Machine
1)working area:1600mm*2600mm/1800mm*2600mm/1600*3000mm
2)working table:auto feeding conveyor
3)laser type :sealed co2 laser tube80W/100W/130W
Fiber Laser Metal Cutting Machine Senfeng
Fiber Laser Metal Cutting Machine Senfeng
1)working table:1300mm*2500mm,1500mm*3000mm
2)fiber laser power:500w/750w//1000w/1200w
SF200F Fiber Laser Marking Machine
SF200F Fiber Laser Marking Machine
1) High speed with galvanometer;
2) 10W/20W/30W fiber device
3) 110*110mm/200*200mm/300*300mm
SF1390B Co2 Laser Cutting Machine
SF1390B Co2 Laser Cutting Machine
1)working size:1300mm*900mm
2)co2 laser
3)Germany Designed
SF3015FL Metal Fiber Laser Cutting Machine
SF3015FL Metal Fiber Laser Cutting Machine
1)working size:1500mm*3000mm
2)fiber power:300w/500w/750w
3)cut 0-3mm SS,0-6mm CS

Top articles

Latest articles

Your browsing history

    Loading...

common problems for laser cutting engraving system

Categories: FAQ Visit: - Release time: 2014-08-08 14:34:00
Font size:【 Large Middle Small Source: Editor: Jenny Author: Jenny

 If the Boot but  laser cutting machine is not start   
1.Check whether the machine electricity is ok
2.check the  main parameters  is correct 
Method:
1.check the electrical wires again
2.set up the parameters refer by software instructions
If Working without laser
1.Check wether the optical path skewing
2.Line problem
Method :
1.Adjust the light path
2.Judgment with plug the rays into the power of the signal terminal

laser workshop

The laser on and off at work   
1.Check whether the water cycle is ok
2.whether the supply voltage is stabilize  
Method :                                                           
1.Clean the water tank and water pump,clear the pipe
2.Add voltage stabilize to power supply
Theonline data can’t be disposed   
1.whether the communication cable is connected
2.whether the software USB is  installed
Method
:    
1.Shutdown and reconnect the cable
2.Reinstall the software and USB drive

Processing size does not  consistent with software set
1.Install the software
2.Adjust action   
Method:
1.install the original software torecover original parameters
2.sized the working area and trim size .calculate refer to software
The control panel  no light
1.Line is loose
Check whether the connecting line is loose  from main board to panel
If Boot reset is limited   
There is  problem of limit switch and signal  
Check parameter of software and limit switch setting
If Carving dislocation
1Electrostatic interference
2Drive parts is loose
    Method:
1.Reconnect ground wire two meters below ground
2.Check if the gear top silk and strap is loose

More information about laser cutting machine , please contact us !

Share:
Previous page:Next page:
Inquire:common problems for laser cutting engraving system
Name:
Name:
Mobile:
E-mail:
Enquiry:
Senfeng Home
About Senfeng
Products
Laser cutting machine
Laser engraving machine
Consulting Center
Senfeng dynamic
Industry News
Frequently Asked Questions
Contact Senfeng
Mail: senfeng@jnsenfeng.com
TEL:+86-531-88737920
Skype: senfeng laser1